EXTRUSION & BLOWN FILM EQUIPMENT

8 BLOWN FILM LINES !!!  JUST PURCHASED !!!

USED ALPINE HDPE CO-EX BLOWN FILM EXTRUSION LINES, NEW APPROXIMATELY 1990. 
EACH LINE CONSISTS OF 65 MM ALPINE 21/1 L/D MODEL HS65 HIGH DENSITY BLOWN FILM EXTRUDER COUPLED WITH 35 MM 21/1 L/D ALPINE MODEL HS35 HIGH DENSITY LOWBOY EXTRUDER BOTH MOUNTED ON COMMON BASE WITH 360 DEGREE ROTATION. EXTRUDERS ARE EQUIPPED WITH COMMON CONTROL PANEL FOR TEMPERATURE CONTROL, EACH WITH 4 INSTRUMENTS, EACH WITH MELT PRESSURE, DRIVE CONTROL, SCREW RPM AND PERCENTAGE MOTOR LOAD. BARREL IS ELECTRICALLY HEATED AIR COOLED,    EACH EXTRUDER EQUIPPED WITH STANDARD HOPPER AND LOADER/RECEIVER. 65 MM EXTRUDER EQUIPPED WITH 100 HP RELIANCE MOTOR WITH RELIANCE MAXPLUS SCR CONTROLLER, 460 VOLT AC INPUT 50/60 HZ. 35 MM DRIVEN BY 50 HP RELIANCE DC MOTOR, EQUIPPED WITH RELIANCE MAXPLUS SCR CONTROLLER, 460 VOLT AC INPUT, 50/60 HZ. EACH EXTRUDER EQUIPPED WITH GROOVED STYLE FEED THROAT.   DIE IS 120 MM 3-LAYER CO-EX DIE (B,A,A) MODEL HK300. NON-ROTATING DESIGN WITH IBC COOLING CAPABILITIES INCLUDING AIR RING BLOWER AND IBC BLOWER WITH RELIANCE MOTORS AND AC INVERTER CONTROLS. IBC PACKAGE INCLUDES COOLING/ STABILIZING TUBE SURROUNDING BUBBLE APPROXIMATELY 5' ABOVE DIE, MOTORIZED BUBBLE STABILIZER WITH PLASTIC IDLER RINGS AT BUBBLE CONTACT AND IBC COLUMN. EQUIPPED WITH 43" WIDE NIP ROLL ASSEMBLY AND COLLAPSING FRAME. HAS 43" WIDE ALPINE SINGLE POSITION SURFACE WINDER FOR APPROXIMATELY 36" DIAMETER ROLLS (LAST USED AT 24" DIAMETER). HAS AUTOMATIC CORE LOAD, MATERIAL CUT AND ROLL START.   INCLUDES ELECTRONIC SAFETY CURTAIN ON DISCHARGE SIDE OF WINDER MANUFACTURED BY SHADOW INFERRED.   HAS EDGE GUIDE MOUNTED ON INFEED SECTION OF WINDER, ELECTRONICALLY ACTUATED. STILL INSTALLED AS OPERATED. PREVIOUSLY USED AT .8 MILL, 287 POUNDS/HOUR HDPE.      

-----------------------------------------------------

EXTRUDERS:

UNUSED 6" NRM 32/1 L/D PACEMAKER III NON-VENTED EXTRUDER . 
HAS 60" CENTER LINE  HEIGHT, ELECTRICALLY HEATED AIR COOLED BARREL. NO MOTOR OR TEMPERATURE PANEL  INCLUDED. NEW 3/2000, SERIAL NUMBER 19360. HAS GEARBOX WITH 19.54/1 RATIO.    

UNUSED 2.5" NRM 24/1 L/D LOWBOY EXTRUDER.
HAS 23" CENTER LINE, 16.95/1 RATIO  GEARBOX DIRECT CONNECTED TO 30 HP AC MOTOR, 230/460 VOLT WITH AC INVERTER. NO  TEMPERATURE PANEL INCLUDED. GEARBOX REPORTED RATED AT 60 HP. NEW 3/2000.   

UNUSED 2.5" NRM 24/1 L/D LOWBOY EXTRUDER.
HAS 23" CENTER LINE, 16.95/1 RATIO  GEARBOX DIRECT CONNECTED TO 30 HP AC MOTOR, 230/460 VOLT WITH AC INVERTER. NO  TEMPERATURE PANEL INCLUDED. GEARBOX REPORTED RATED AT 60 HP. NEW 3/2000.   

USED 80 MM GLOUCESTER CONTRA COOL LOWBOY EXTRUDER.
25/1 L/D WITH 23" CENTER  LINE HEIGHT OF BARREL. EXTRUDER MODEL 80250R2, S/N 34549/01. HAS 13.88/1 RATIO  GEARBOX BUT NO MOTOR, NO PANEL, NO SCREW.   

--------------------------------------------------------------

SCREEN CHANGERS:

USED 6" BERINGER MODEL UL60 SLIDE PLATE SCREEN CHANGER, SERIAL NUMBER UL399.
INCLUDES HYDRAULIC PUMPING SYSTEM. WILL ACCOMMODATE MAXIMUM 10,000 PSI HEAD  PRESSURE. 

(2) USED 2.5" BERINGER HYDRAULIC SLIDE PLATE SCREEN CHANGERS.
WITHOUT HYDRAULIC  PUMPING SYSTEM.  

---------------------------------------------------------------

BAG MACHINES:

USED 41 INCH WIDE FMC BOTTOM SEAL "HANDLE TIE" BAG MACHINE.  
UNIT EQUIPPED WITH  2-POSITION UNWIND STAND FOR 24" DIAMETER ROLLS INCLUDING MANUAL EDGE GUIDE. BAG  MACHINE IS DUAL LANE DESIGN, HAS POST GUSSET ASSEMBLY WITH DC MOTOR AND SCR CONTROL, BOTTOM SEAL BAG MACHINE INCLUDING COMCO MECHANICAL INTERMITTENT DRIVE  DIRECTLY CONNECTED TO DC MOTOR WITH SCR CONTROL. DC MOTOR UTILIZED FOR DRIVING  CAM ON SEAL BAR, COMCO DRIVE, USED FOR RATIO BETWEEN SEAL BAR AND DRAW ROLLERS.  ALSO INCLUDED IS DUAL DIE CUT STATIONS FOR T-SHIRT OR HANDLE TIE BAG CUT OUTS,  DRIVEN BY AC MOTOR WITH INVERTER CONTROLLER AND BELT TAKE-AWAY FOR FINISHED  BAGS. NEW 1981. SERIAL NUMBER B1462.   

----------------------------------------------------------

3 EXTRUSION FILM WINDERS - JUST PURCHASED !

#1 - USED 54 INCH WIDE MARSHALL & WILLIAMS 3-POSITION TURRET WINDER. SERIAL NUMBER 39314. 
560 VOLT AC INPUT, WILL ACCOMMODATE MAXIMUM 4000 LB. ROLL (52" O.D.). HAS MOTOR FOR EACH POSITION, WITH SOLID STATE CONTROL. NEW APPROXIMATELY 1999. HAS ROLL TAKE OFF AND CANTILEVER HOIST. MOUNTED ON WINDER FRAME. UTILIZES 8 INCH CORES. PREVIOUSLY USED ON PS SHEET EXTRUSION LINE FOR THERMOFORMING. (Photos available)  

#2 - USED 54 INCH WIDE PARKINSON 3-POSITION TURRET WINDER.
WILL ACCOMMODATE MAXIMUM  4000 POUND ROLL (PS AT ESTIMATED 52 INCH O.D.). UTILIZED 8 INCH CORES, WITH AIR ENGAGED SHAFTS, TAPERED TENSION CONTROL, AUXILIARY ARMS FOR ROLL TAKE OFF, AND CANTILEVER MOUNTED HOIST. SERIAL NUMBER 004024-01. NEW APPROX. 1999. PREVIOUSLY USED ON PS SHEET EXTRUSION LINE FOR THERMOFORMING. (Photos available)  

#3 - USED 64 INCH WIDE PARKINSON 3-POSITION TURRET WINDER.
WILL ACCOMMODATE MAXIMUM  48 INCH DIAMETER ROLLS (2000 LB. MAXIMUM). SERIAL NUMBER 78-870. HAS 4-SPEED GEARBOX,    HYDRAULIC ROLL TAKE OFF, TORQUE MOTORS AND CONTROLS.   PREVIOUSLY USED ON PS SHEET EXTRUSION LINE FOR THERMOFORMING. (Photos available)  

---------------------------------------------------------------

EXTRUSION COMPOUNDING LINE DOWNSTREAM EQUIPMENT:

SUPER SACK UNLOADER (UNUSED)

UNUSED SUPER SACK UNLOADER. INCLUDES FORK TRUCK LOADED FRAME FOR HANGING  SUPER SACKS. FRAME INCORPORATES (2) AIR ACTUATED "THUMPERS" FOR KEEPING  MATERIAL FLOWING FREELY OUT OF SUPER SACK. ALSO INCLUDES APPROXIMATE  3 FOOT x 3 FOOT x 3 FOOT DEEP STAINLESS STEEL RECEIVER FOR PNEUMATIC CONVEYING OF MATERIAL TO PROCESS LINE. (Photo available)   

FLEXICON SUPER SACK FILLER (UNUSED)

UNUSED FLEXICON SUPER SACK FILLING STATION. HAS FRAME FOR HANGING SUPER  SACK, FLEXICON FLEXIBLE SCREW CONVEYOR CONNECTING RECEIVER BIN WITH AC  MOTOR AND INVERTER SPEED CONTROLLER MOUNTED OVER SUPER SACK AND  APPROXIMATELY 15 CUBIC FOOT STAINLESS STEEL BIN WITH CYCLONE RECEIVER FOR  PNEUMATICALLY CONVEYING MATERIAL TO FEED PORTION OF SUPER SACK. INCLUDES  OPERATOR PANEL WITH PUSH BUTTON STATIONS AND ABOVE MENTIONED INVERTER.  (Photo available)   

------------------------------------------------------

MIXERS AND BLENDERS

PATTERSON KELLEY 50 CUBIC FOOT TWIN SHELL BLENDER 
USED PATTERSON KELLEY 50 CUBIC FOOT STAINLESS STEEL TWIN SHELL BLENDER. BLENDER RATED AT 100 POUNDS PER CUBIC FOOT, MOUNTED ON PEDESTALS WITH 7.5 HP GEAR HEAD DRIVE AND BRAKE BUT NO INTENSIFIER BAR. HAS BUTTERFLY VALVE   

--------------------------------------------------------

                           And more coming soon!

We are one of the largest stocking dealers of plastics molding machinery in the United States, and have been selling plastics machinery worldwide for over 35 years. Our inventory is constantly changing, and we are often liquidating complete plants. Please keep in contact with us so that we can keep you informed of our latest purchases.