Timberline Machinery Inc.
7 Pittsburgh Ave                           Nashua, New Hampshire 03062, USA
Phone (603) 889-7233         Fax (603) 889-7300        Call Ed Makepeace

Close This Window

   Request Quotation or Additional Information

   Make an offer on this machine!


1989 HUSKY ONE-STEP ^PET STRETCH-BLOW MOLDER!

Ref #

Manufacturer

Model

Year

Production Capacity (bottles/hr)

Comments

30099 

Husky 

XL2225RS-ITS 

1989 

3000 

preform injection molder with integrated ITS stretch-blow molder, excellent condition, loaded with options 


1989 HUSKY ONE-STEP ^PET STRETCH-BLOW MOLDER!

* HUSKY XL225RS ^PET PREFORM INJECTION MOLDER 
* INTEGRATED ITS STRETCH- BLOW MOLDER
* ROBOT PACKAGE FOR PREFORM HANDLING

Injection specifications:
- Reciprocating screw injection unit 
- Screw diameter   2.36 inches 
- Screw L/D ratio  25/1
- Compression ratio and screw designed for PET
- Maximum screw speed   75 RPM
- Injection stroke   9.4 inches
- Injection volume   41 cubic inches
- Maximum injection pressure  14,500 psi
- 5 step injection velocity and 3 step hold pressure
- Powered hopper shutoff
- Hydraulically operated nozzle shutoff valve

Clamp specifications:
- Clamp pressure  250 tons
- Distance between tie bars  24.4 x 24.4 inches
- Maximum clamp stroke   21.6 inches
- Minimum/maximum mold thickness   8.9 to 28.5 inches   
- Maximum open daylight   50.1 inches
- Maximum hydraulic ejector stroke   9.8 inches

Control panel package:
- Siemens Model 1500 microprocessor controls
   - this system provides integrated high speed control 
     with extensive diagnostic capabilities
    - it also provides capability to integrate into a 
     plant-wide supervisory system, store 10 mold set-ups,
     and allows remote uploading and downloading

ITS integrated stretch- blow molding machine:
- Conditional tunnel with 7 heating modules and
  2 cooling modules 
- 100 ton mono-toggle blow molding clamp
  - ITS stretch rod stroke  13.8 inches
  - ITS stretch rod diameter  0.625 inches
  - Two-stage air system  750 psi maximum
  - base plug actuator
- ITS carriers have a pitch of 5.91 inches
- Locating bushings for quick mold change

ITS robot package for preform handling:
- Air operated robot attached to stationary platen 
  with 59.1 inch Z-axis stroke
- Y-axis: servo driven with 18.1 inch stroke
- Hydraulic compound tilt mechanism of 90 degrees
  for take-out plate
- Vacuum/blow system to assist part removal

General specifications:
- Proportionally controlled cartridge valves
- Water saver valve
- Automatic central lubrication
- Electronically monitored oil filters
- Mold temperature control package including a heater 
  receptacle box mounted onto the front of the stationary 
  platen and includes 2 temperature control circuits
- Four auxiliary 10-amp duplex plug receptacles located at:
  - Front side by operator's station of XL225RS
  - Rear side of XL225RS injection unit
  - Operator's side of ITS blow molder
  - Near power panel of ITS machine
- Additional emergency stop buttons, for a total of three

Electrical specifications:
- Hydraulic pump motor   50HP
- Injection barrel heaters   32KW
- Mold heaters   18KW
- ITS stretch- blow molder heaters   96 KW

-----------------------------------

NOTE: Although machinery descriptions are believed to be accurate and 
      are from sources deemed reliable, they are not guaranteed and we 
      invite your inspection prior to purchase.
We are one of the largest stocking dealers of plastics molding
machinery in the United States, and have been selling plastics
machinery worldwide for over 35 years. Our inventory is constantly
changing, and we are often liquidating complete plants. Please keep
in contact with us so that we can keep you informed of our latest
purchases.

Close This Window