Timberline Machinery Inc.
7 Pittsburgh Ave                           Nashua, New Hampshire 03062, USA
Phone (603) 889-7233         Fax (603) 889-7300        Call Ed Makepeace

Close This Window

   Request Quotation or Additional Information

   Make an offer on this machine!


JUST PURCHASED - ONLY 1700 HOURS! - IN LAB - 33 POUND 1997 HARTIG DAVIS-STANDARD BLOWMOLDER!

Ref #

Manufacturer

Model

Year

Shot Capacity (pounds)

Head Configuration

Comments

30072 

Hartig Davis-Standard 

MCP45S33 

1997 

33 

single 

in lab - only 1700 hours - loaded with options! 


JUST PURCHASED!

1997 HARTIG DAVIS-STANDARD 33 to 42 POUND BLOW MOLDER
FROM LAB!   ONLY 1700 HOURS!  LIKE NEW!  LOADED WITH OPTIONS!
LATEST SPIRAL HEAD DESIGN FOR QUICK COLOR CHANGEOVERS!
ORIGINAL COST OVER $900,000!   
SIGNIFICANT SAVINGS ON A LIKE-NEW MACHINE!

MODEL: MCP45S33-4872S200
CLAMP TONNAGE: 200 (Expandable to 300 tons!)
EXTRUDER SIZE: 4.5" DIAMETER WITH 250HP DC DRIVE
SHOT SIZE: 33 pounds HDPE, 42 pounds engineering materials
LATEST SPIRAL DESIGN HEAD FOR QUICK COLOR CHANGE AND ENGINEERING MATERIAL CAPABILITIES
DROP RATE: 7 lb/ sec.
CONTROLS: BARBER COLEMAN MACO 8000
DUAL CHANNEL 100 POINT PARISON PROGRAMMER
MOTORIZED ROLL AWAY PRESS
48 INCH WIDE X 72 INCH LONG CLEAR PLATEN
AUTOMATIC CANTILEVERED PART TAKE OUT FOR UNLIMITED PRESS ACCESS
10 SETS OF TOOLING (4 TO 14 INCH), SPARE SCREW, ETC
LOADED WITH OPTIONS!


Component Specifications

* 4.5 inch diameter, 24:1 L/D High Torque Extruder Section

* Conventionally flighted feedscrew machined from SAE 4140 steel 
with flights hard surfaced with Colmanoy 56 for wear resistance.  

* The gear reducer used on the Hartig high torque extrder is a fixed 
ratio design UNIX 7.1 for compactness and ease of maintenance.  It is 
rated at 250 HP at 100 RPM with a 1.6 service factor for extended life.

* The thrust bearing used to absorb the thrust load generated by the
feedscrew is a high quality Timken T-811 with a B-10 life of 269,900 
hours at 5,000 psi and 100 RPM.

* Our tangential opening feedthroat is a proven design supplied on all 
Hartig extruders.  It is designed to assure positive feeding of virgin 
and virgin/regrind blends and is machined of high strength ductile iron.  
It's construction provides a core for water cooling.

* Attached to the feedthroat is a high flow hopper system engineered 
for bridge-free operation.  Each hopper has a dump chute for quick 
material change and a sight glass for visual level indication.

* The extruder barrel is fabricated from SAE 4140 steel with a xaloy 
liner matched to the Hartig feedscrew for extended production.  All 
barrels are pressure rated 10,000 PSI.

* Extruder temperature control is provided over the entire length of 
the barrel.  The extruder is divided into four (4) zones of finned cast 
aluminum heaters for heating and individual high air volume blower for 
cooling.  The barrel and heaters are covered with insulated guards.

* The extruder drive is a highly regulated 250 HP D.C. SCR package with 
a 1750 RPM motor which provides constant torque to the feedscrew.  
Included in the system is an open drip-proof motor, cooling blowers and
intake filters.  All drive controls are conveniently mounted in the main 
blow molder control panel.  The drive operates under 460 volt, 3 phase,
60 cycle current.

Accumulator Head - 33 pounds HDPE - 42 pounds engineering materials

* The Davis Standard  spiral accumulator head's unique design produces 
a parison void of a continuous knitline through it's wall.  This allows the 
utmost in structural integrity while producing a very uniform wall thickness.  
As a direct result, finished products can usually be light weighted for a 
significant material savings.

* Our tandem hydraulic system assures a uniformed alignment of the ram 
and tooling forces for long, trouble free operation.  Through the use of 
this system, the inner cylinder strokes the tooling while the annular
outer cylinder strokes the ram.

* Shot size                       33 pounds HDPE, 42 pounds engineering materials
* Drop rate maximum               7 pounds/second
* Ram stroke                      7 inches 
* Tooling cylinder stroke         2 inches
* Tooling diameter (minimum)      6 inches
* Tooling diameter (maximum)      18 inches
* Total heater KW                 59 KW
* Includes one set of head tooling.

Press - 48 inches wide X 72 inches high clamping section (M.C.P.)

* Hartig's press designs are based on the unique principal of pulling 
the molds closed to achieve full clamp tonnage.  This concept allows 
all custom Hartig presses to bring the mold faces in parallel, as the 
end frames have no load on them.

* The platens are closed in high speed with individual, small bore 
cylinders to minimize oil flow for maximum efficiency.  High pressure 
clamping is accomplished by rotating knuckle clamps which, when engaged, 
pull the molds closed.  These short stroke, large bore cylinders 
generate high tonnage, but with little oil flow.  This method assures 
no deflection of the  end frames and no axial stressing of the tie bars. 

* Further, Hartig's MCP has platens which ride on ways.  This takes the 
dead platen and mold weight off the tie rods to further assure no 
deflection takes place to disturb parallelism.

* To bring the platens together on center repeatedly, dual chain 
synchronization is applied.  Mounted out of the press working area, the 
adjustable chain systems are located on the front and back of the 
platens so that forces are distributed equally.  Easy adjustment can 
be made for off center close or adjustment.

* Also, standard on all presses is a safety system of electrical and 
hydraulic interlocks as well as whiskers to sense if an operator is in 
the press area.  Emergency stops are located at five points around the 
machine and the entire press area is enclosed by expanded metal.  This
assures that all pinch points are guarded for safe operation.

Additional specifications:
* Clamp tonnage:                        200 tons (expandable to 300 tons)
* Maximum platen opening                96 inches
* Minimum platen opening                18 inches
* Motorized vertical height adjustment     +/- 5
* Side to side adjustment
* Press wheels on track
* Manual press shut height adjustment

Controls

* The control panel is a three-door NEMA enclosure with main power 
disconnect shock mounted on the unitized base wired 460 volts/ 3 phase/ 
60 hertz.  The following components are included:

* Barber-Colman MACO 8000 Microprocessor control system with Lumitech
display panel for control of the following functions:

* Control temperature on all zones displayed via operator's station.  
The system provides independent zone temperature control and can be 
independently tuned. 

* Total machine sequential control up to 100 independent timer 
functions available depending on number of sequence modules in system.

* Solid state cartridges for program and control parameter storage.

* Parison process control with individual weight and die gap settings 
and graphic display of profile setpoints.

* The exclusive use of individual control modules allows initial 
system to be easily expanded to meet future requirements. 

* D.C. drive controls
* Amp meter
* Tachometer
* Variable speed control
* Motor starters for all hydraulic AC motors
* Mercury contactors on heat zones
* Fuse block and fuses
* Control transformer

Hydraulics

* The Hartig hydraulic power system was designed and developed to work 
efficiently to operate the press, accumulator head(s) and auxilliary 
functions.

* The power untit is floor mounted with integral drip pan, sight level 
guagees, and for ease of maintenance all port and valve designations 
are stamped on the manifold.  Oil cooling and 3 Micron system filtration 
is accomplished through a separate kidney loop and filter bypass alarm.  
Low oil level and high oil temperature alarms are also included.  
Additionally, a shell and tube heat exchanger is outfitted with a water 
saver valve.

* Valving is cartridge type for the highest oil flow and fastest 
response of any valve design available today.  Due to the cartridge 
valve's design, the wear characteristics are far superior to that of 
spool valves.  All valves are manifold mounted and utilize electrical 
connectors with integral LED's and surge suppressors.

* Press and ram speed are independently proportionally variable through 
the MACO 8000 for tight process control and shock-free performance.

* The power unit is floor mounted with integral drip pan, sight level 
guage, pressure guages, and for ease of maintenance, all port and valve 
designations are stamped on the manifold.

* AC horsepower               50
* Main pump GPM               32
* Accumulator size            60 gallons
* Reservoir capacity          200 gallons
* System filtration           3 micron

Pneumatics

* Includes required regulators, filter and valving for air blow and pre-blow.

Base

* Main base is a unitized construction and serves as a mounting 
platform for extruder and accumulator head.  Stairs and diamond plate 
catwalk are provided for maintenance and set-up of extruder and 
accumulator head.

Plus more! LOADED WITH OPTIONS!
* Retractable top blow pin assembly
* Part stripper plates
* Mold cooling water manifolds
* For single head (4) 4-station manifolds:  8 zones in-8 zones out
* Motorized press rollout
* Motorized press height adjustment
* Control cabinet air conditioner
* Amp meters mounted on control cabinet for each heating zone
* Light over hydraulic power unit
* Tooling stand
* Air receiver tank assembly, 240 gallon, connected and mounted to the 
  machine frame including pressure guage, safety valve and regulator
* Hopper magnet, drawer type
* Rupture disc limit switch
* Pneumatic hopper shutoff
* One (1) automatic part removal system consisting of top part grabber 
  utilizing cooled fingers to grab the parison and remove it from the 
  press.  This entire assembly is cantilever mounted to machine frame to 
  allow unlimited access to press
* 4 station hydraulic manifold utilizing directional valves for 
  auxiliary functions for dual heads
* 4 station pneumatic manifold for auxiliary functions for dual head

-----------------------------------

NOTE: Although machinery descriptions are believed to be accurate and 
      are from sources deemed reliable, they are not guaranteed and we 
      invite your inspection prior to purchase.
We are one of the largest stocking dealers of plastics molding
machinery in the United States, and have been selling plastics
machinery worldwide for over 35 years. Our inventory is constantly
changing, and we are often liquidating complete plants. Please keep
in contact with us so that we can keep you informed of our latest
purchases.

Close This Window