Timberline Machinery Inc.
7 Pittsburgh Ave                           Nashua, New Hampshire 03062, USA
Phone (603) 889-7233         Fax (603) 889-7300        Call Ed Makepeace

Close This Window

   Request Quotation or Additional Information

   Make an offer on this machine!


UWM-4 (Ultra Wide Mouth) ^PET stretch blow molder - Priced right !!!

Ref #

Manufacturer

Model

Year

Production Capacity (bottles/hr)

Comments

30068 

B&G 

UWM-4 

1993 

4000 

wide mouth capability, Priced right !!! 


1993 B&G Universal UWM-4 ^PET Stretch-Blow Molding Machine
* Features 4 Blow Molds for up to 1 Gallon (4 Liter) Containers
* Wide mouth capability!!!
PRICED RIGHT !!!

Combine this in-stock fully automated ^PET stretch blow molding line
with one of our in-stock fully automated preform manufacturing lines
for a fuuly automated ^PET resin to bottle manufacturing system:
  - see our Husky XL300P complete preform manufacturing system, reference number 10077

SPECIFICATIONS OF THIS B&G STRETCH BLOW MOLDING LINE:

Preform Heater Section:
* Heater Length   64 inches, 1630 mm
  (22 inches Condition and 40 inches Profile)       
* Number of heating stations    17
* Equilibration length (No. of stations)    6-9
  min.- max.(3.75* or 96 mm per station)
* Center distance between preforms  3.78 inches, 85 mm
* Center distance between lanes  8 inches, 152 mm
* Number of heater elements per bank   20
  (one bank per preform lane)   
* Total number temperature controlled zones (per bank)  20
  Total per machine   60
* Total heater capacity  69KW
* Oven loading height  79 inches, +/- 0.3 inches 
                       or 2005 mm +/- 10 mm
  (from floor) with levalore in place       
* Total number of pallets   33
* Total number of nose holders  132

Mold Unit:
* Platen and clamp specifications    88 tons
* Platen size (W & H)   24 x 16.38 inches, 610 x 415 mm
* Maximum daylight      13.50 inches
* Clamp Stroke (3.00 inches x 2)   6.00
* Bottom Stroke  3.0
* Mold Specifications:
  Overall mold dimensions, each hull:
     (W x H x D) 8 x 13.875 x 3.75 inches
  Total mold thickness   7.5 inches
  Mold bottom diameter, max (3 piece molds)  4.247 inches

Preform and Stretch Blown Container Data
  (typical ranges only, do not use for preform design)
* Preform Specifications (.06 per side support ring recommended)
* Neck finish, min./max.   18 mm/89 mm
* Support ring diameter (max.)     3.82 inches
* Body diameter, min./max.   0.82 inches, 3.60 inches
* Overall length, max.  8 inches
* Maximum wall thickness   0.190 inches, 4.8 mm

Stretch Blown Container Specifications:
* Neck finish, min./max  18 mm/110 mm
  (finishes larger than 89 mm are blown)
* Maximum diameter  6.75 inches
* Maximum height (w/o finish)  15 inches
* Approximate volume, max. 1 gallon, 4 liter

Power and Service Requirements:

Electrical:
* Power supply (volts/phase/cycle)   460/3/60
* Number of electric motors       6
* Total Rated H.P.  32
* Full load power requirements (controls, motors, heaters)   91KW

Hydraulic System
* Oil Reservoir capacity   120 gallons, 460 liters
* System pressure, max.    1000 psig, 70 kg/cm2

Cooling system      Water
* Volume (min.) 0 temperature (max.)   25 gpm at 85 inches F
* Inlet and outlet connections    1-1/4 inches NPTF
* Auxillary mold chiller (mold and oven)   161,200 BTUH
* Inlet and outlet connections   1 inch NPTF
* Compressed air system - low pressure house air   100 psig
* System pressure, max. -- High pressure air    750 psig
* Inlet connection   2 inches NPTF

Typical Process Settings
  (2-piece, 2-liter bottle, 2.7 sec.cycle)
  (1-piece, 2-liter bottle, 3.5 sec cycle)
* Hydraulic system pressure   600 psig
* Compressed air pressure  450 psig/550psig
  (min. recommend 20 percent increase)
* Compressed air volume, min   265 sc/m
  (recommend 30 percent increase)  
* Mold chilling water temperature   +40 degrees F
* Volume and pressure     60 gal./min. at 80 psig

Typical Process for One Gallon (4 sec. Cycle) 
* Water Temperature   +40 degrees F
* Temp. Differential (in and out)  3 degrees F
* Compressed air volume   424 sc/m

Machine Dimensions Overall - Nominal
* Length                           200 inches
* Width                            109 inches
* Total ceiling height required    140 inches
* Total installation floor area    127 square feet
* Shipping weight                  12 tons

-----------------------------------

NOTE: Although machinery descriptions are believed to be accurate and 
      are from sources deemed reliable, they are not guaranteed and we 
      invite your inspection prior to purchase.
We are one of the largest stocking dealers of plastics molding
machinery in the United States, and have been selling plastics
machinery worldwide for over 35 years. Our inventory is constantly
changing, and we are often liquidating complete plants. Please keep
in contact with us so that we can keep you informed of our latest
purchases.

Close This Window