![]() |
7 Pittsburgh Ave Nashua, New Hampshire 03062, USA |
Phone (603) 889-7233 Fax (603) 889-7300 Call Ed Makepeace |
Ref # | Manufacturer | Model | Year | Shot Capacity (pounds) | Head Configuration | Comments |
---|---|---|---|---|---|---|
30181 | Sterling Davis-Standard | SE3505D | 1997 | 5 | dual | 1-owner machine with only 22,000 hours! excellent condition! Maco 6500, 21 inch head spacing, 42 x 36 inch clear platen, 125HP 3.5 inch extruder |
1997 STERLING DAVIS-STANDARD BLOW MOLDING MACHINE DUAL 5 POUND (2.3 kg) ACCUMULATOR HEADS * ONE OWNER MACHINE WITH ONLY 22,000 HOURS !! * $800,000 REPLACEMENT COST !! * CLAMP TONNAGE: 65 TONS * EXTRUDER SIZE: 3.5 INCH (90MM) DIAMETER - 24:1 L:D FOR HIGH PLASTICIZING AND PRODUCTION OUTPUT * EXTRUDER DRIVE: 125HP HYDRAULICALLY DRIVEN * SHOT SIZE: DUAL HEADS, 5 POUNDS (2.3 kg) HDPE PER HEAD * HEAD SPACING: 21 INCH CENTERS * PART STRIPPER MECHANISM * CONTROLS: BARBER COLEMAN MACO 6500 * DUAL CHANNEL 100 POINT PARISON PROGRAMMER * 42 INCH WIDE X 36 INCH LONG CLEAR PLATEN * 3 TO 8 INCH TOOLING RANGE * 39 inch maximum clamp open daylight * 15 inch minimum clamp closed daylight * Vertical platen height adjustment +/- 4 inches * Side to side platen adjustment +/- 3 inches * Front to back platen adjustment +/- 3 inches * Manual press shut height adjustment Additional specifications: EXTRUDER SECTION: * Continuous extrusion * High performance feed screw with Colmonoy 56 hard surface flights * Sterling barrel assembly fabricated of 4140 alloy steel with bimetallic inlay of Xaloy 102 or equivalent and a bolt type front flange. * Hopper drawer magnet ACCUMULATOR HEADS: * First in, first out material flow * Common shooting ring and six push rods * One servo valve and DCDC transducer per head * Individual control of flow (speed) of accumulator shooting with digital readout * Part stripper assembly CLAMP SECTION: * Manual central lubrication system MICROPROCESSOR MACHINE CONTROL: * Maco 6500 * Operator station is integrally mounted in main cabinet with amber screen electro- luminescent display with key panel and set up recipe storage * Speed control for hydraulic drive * Output sequence cards * Input sequence cards * Parison control card * Analog I/O card * Real time clock * Recipe storage cartridge * Power supply and data handler * Microprocessor monitors hydraulic filter switches and alarms * Cycle time and cycle simulator MAIN ELECTRICAL CONTROL PANEL: * Three door construction * Motor starter for main hydraulic AC motor * Ammeters on each heater zone for heater burn-out detection * Mercury contactors with circuit breakers on heater zones * Isolation transformer for microprocessor * Main disconnect switch * DC drive controls * Panel climate control devise * Voltage regulator PROPORTIONAL HYDRAULIC POWER UNIT: * 140 gallon tank capacity * 25HP AC motor * 125HP AC motor with 1750 RPM for hydraulic screw drive * One (1) 10-gallon accumulator * Variable volume pump with a 45 gallon per minute maximum displacement * Dual head operation * Electronically controlled operating extruder drive and parison push-out * Secondary pump 7.4 gallons per minute, pressure compensated, operates clamp and parison programming MAIN BASE HOUSES THE FOLLOWING: * Extruder * Accumulator heads * Hydraulic unit * Control cabinet * Press AIR BLOW SYSTEM * 7 station air manifold system HYDRAULIC/PNEUMATIC * Filtrol hydraulic supplimental filter assembly * 4 auxiliary air circuits * Auxiliary hydraulic manifold PRIMARY POWER WIRING: - Maco 6500 is designed to operate from a 102-132 VAC, 50/60 Hz, single phase power source. Each module contains its own power supply which provides all operating voltages for the module circuitry. Control equipment should not be connected to power sources subject to extreme voltage fluctuations caused by switching heavy loads. A voltage step-down isolation or voltage regulation transformer installed in the control cabinet is supplied.
----------------------------------- NOTE: Although machinery descriptions are believed to be accurate and are from sources deemed reliable, they are not guaranteed and we invite your inspection prior to purchase.
We are one of the largest stocking dealers of plastics molding machinery in the United States, and have been selling plastics machinery worldwide for over 35 years. Our inventory is constantly changing, and we are often liquidating complete plants. Please keep in contact with us so that we can keep you informed of our latest purchases.