Timberline Machinery Inc.
7 Pittsburgh Ave                           Nashua, New Hampshire 03062, USA
Phone (603) 889-7233         Fax (603) 889-7300        Call Ed Makepeace

Close This Window

   Request Quotation or Additional Information

   Make an offer on this machine!


1992 DUAL 15 POUND STERLING DAVIS-STANDARD BLOW MOLDER !!! EXTRA LARGE PRESS !!!

Ref #

Manufacturer

Model

Year

Shot Capacity (pounds)

Head Configuration

Comments

30160 

Sterling Davis-Standard 

SE4515D 

1992 

15 

dual 

36 inch head centers, extra large 74 x 60 inch clear platen, part take-out 


JUST AVAILABLE!
THIS MACHINE WILL NOT LAST LONG!

1992 STERLING DAVIS-STANDARD 
DUAL 15 POUND (6.5 kg) ACCUMULATOR HEAD BLOW MOLDER

NOTE - OPTIONALLY AVAILABLE SINGLE HEAD:
A SINGLE 40 POUND (17.5 kg) STERLING DAVIS-STANDARD HEAD THAT WE CURRENTLY 
HAVE IN STOCK IS OPTIONALLY AVAILABLE FOR THIS 1992 BLOW MOLDER

* CLAMP TONNAGE: 180 TONS
* EXTRUDER SIZE: 4.5 INCH DIAMETER, 24:1 L:D
* EXTRUDER DRIVE:  200HP DC
* SHOT SIZE: DUAL HEADS, 15 POUNDS (6.5 kg) HDPE PER HEAD
* HEAD SPACING: 36 INCH CENTERS
* CONTROLS: BARBER COLEMAN MACO 8000 
* DUAL CHANNEL 100 POINT PARISON PROGRAMMER
* 74 INCH WIDE X 60 INCH LONG CLEAR PLATEN
* AUTOMATIC PART TAKE OUT FOR UNLIMITED PRESS ACCESS
* 3 TO 15 INCH TOOLING RANGE 
    * Note - we have 11 sets of tooling in stock that are optionally 
             available for these 15 pound Sterling accumulator heads

* 66 inch maximum clamp open daylight 
* 10 inch minimum clamp closed daylight
* Vertical platen height adjustment     +/- 4 inches
* Side to side platen adjustment         +/- 3 inches
* Front to back platen adjustment       +/- 3 inches
* Manual press shut height adjustment

Additional specifications:

EXTRUDER SECTION:
* Model 280 gear reducer with mechanical rating of 350HP at 100 RPM screw speed
* Continuous extrusion
* High performance feed screw with Colmonoy 56 hard surface flights 
* Sterling barrel assembly fabricated of 4140 alloy steel with bimetallic inlay of Xaloy 102 or equivalent 
  and a bolt type front flange.
* Cast aluminum heaters with integral cooling coils.
* Closed loop cooling system.
* Rupture disk, pressure reducer and indicator.

ACCUMULATOR HEADS:
* First in, first out material flow
* Common shooting ring and six push rods
* One servo valve and DCDC transducer per head
* Individual control of flow (speed) of accumulator shooting with digital readout

CLAMP SECTION:
* Relative platen speed   1200 inches per minute
* Mechanical adjustable stops to perform as movable guide rods 

MICROPROCESSOR MACHINE CONTROL:
* Maco 8000
* Lumitech electro luminescent Touch-Trol operator control station
     Remote and accessible with swing-away feature
     Set-up operation control buttons and switches
     Ammeter, tachometer, and speed control for DC drive
     Pressure indicator
* System/ Insta-set module
* Sequence module
* Five heat/cool module - six zones
* Temperature heat only modules - two 12-zones
* Linear positioning
* Multi-parameter process control speed for parison drop
* Pressure flow module
* Cabinet is provided with space for a maximum of 15 modules

MAIN ELECTRICAL CONTROL PANEL:
* Three door construction
* Motor starter for main hydraulic AC motor
* Ammeters on each heater zone for heater burn-out detection
* Mercury contactors with circuit breakers on heater zones
* Isolation transformer for microprocessor
* Main disconnect switch
* DC drive controls
* Panel climate control devise
* Voltage regulator

PROPORTIONAL HYDRAULIC POWER UNIT:
* 200 gallon tank capacity
* 40HP AC motor
* Pre-piped and pre-wired
* Dual head operation
* Return line filtration 10 micron
* Heat exchanger 27HP with inlet temperature of 85F and oil flow of 8 GPM
* Independent recirculating system for hydraulic heat exchangers with independent pump and motor
* Three (3) 10-gallon accumulators
* Pump pressure compensated and fixed 20.8 GPM
* Necessary valves for blow mold operation of press and head
* Shooting and clamp manifolds for valve mounting
* Electronic control system

MAIN BASE HOUSES THE FOLLOWING:
* Extruder
* Accumulator heads
* Hydraulic unit
* Control cabinet
* Press
* The upper deck has an open-up design for ease of head removal and/or installation, and it also 
significantly reduces the ceiling height required above the machine.

PRIMARY POWER WIRING:
- Maco 8000 is designed to operate from a 102-132 VAC, 50/60 Hz, single phase power source.  
Each module contains its own power supply which provides all operating voltages for the module 
circuitry.  Control equipment should not be connected to power sources subject to extreme voltage 
fluctuations caused by switching heavy loads. A voltage step-down isolation or voltage regulation 
transformer installed in the control cabinet is supplied.

-----------------------------------

NOTE: Although machinery descriptions are believed to be accurate and 
      are from sources deemed reliable, they are not guaranteed and we 
      invite your inspection prior to purchase.
We are one of the largest stocking dealers of plastics molding
machinery in the United States, and have been selling plastics
machinery worldwide for over 35 years. Our inventory is constantly
changing, and we are often liquidating complete plants. Please keep
in contact with us so that we can keep you informed of our latest
purchases.

Close This Window