|7 Pittsburgh Ave Nashua, New Hampshire 03062, USA|
|Phone (603) 889-7233 Fax (603) 889-7300 Call Ed Makepeace|
Close This Window
Shot Capacity (pounds)
immaculate condition, 36 inch head spacing, large 74 x 84 inch clear platen, 4.5 inch 200 HP extruder, part take-out
1996 Graham Engineering dual 22 pound accumulator head blow molder - IMMACULATE !!! * 1996 Graham Engineering dual 22 pound accumulator head blow molding machine * Extra large 74 inch wide x 84 inch high clear platen * 36 inch head spacing * Automatic part take out * Barber Coleman EL microprocessor machine controls * Dual station 100 point parison programming * Immaculate condition Specifications and Features: ACCUMULATOR HEAD Dual head - 36 inch centers Shot size - 22 pounds per head (HDPE .2 melt index) Plastic flow is first in, first out Speed control on parison push out Parison programming microprocessor controlled Includes linear position pot, LVDT transducer and servo solenoid valves for each head - each head has total independent control Two (2) shoot cylinders per head Shoot cylinders manual/hydraulic retract for clean out of internal head parts One (1) program cylinder Two (2) bleed out ports for weepage Plunger with one (1) heat zone Head body with extruded aluminum calrod heaters Bushing die tooling with one (1) heat zone Head tooling range 5 inches to 18 inches Air flow straight through entire head With the plunger purged (down), there is minimum plastic inventory in the head from the face of the plunger to the bottom to tooling Head body includes four (4) adjusting bolts for adjusting parison Includes mechanical zero adjustment mechanism for head tooling EXTRUSION SYSTEM * 4.5 inch, 200 HP, 24:1 L/D extruder High efficiency feedscrew for HDPE Wear resistant bimetallic barrel Rupture disc and pressure transducer Feed throat is grooved and water cooled Front barrel support for thermal expansion Air cooled cast aluminum heaters with air blowers Heavy duty gear box with built in thrust bearing (rated at 10,000 psi) with mechanical rating of 400 HP at 100 RPM rpm feedscrew speed System designed for continuous extrusion with safety shut down overfill feature System rated at 1300 pounds per hour HDPE (.2 melt index) * 200 HP AC drive motor Notes: - Graham Engineering's innovative head design allows for fast internal cleaning without major tools or special devices, (disassembly/reassembly) - Substantial head support arms keep them in proper precise position and on centerline - Support arms are designed to allow for thermal expansion/contraction CLAMP STATION Clear platen dimensions - 74 inches wide x 84 inches high Daylite maximum open - 66 inches Daylite minimum close - 16 inches Clamp lock-up tonnage - 190 tons at 2500 psi Motorized vertical platen centerline adjustment ±2 inches Motorized roll out for mold changeover and adjustment ± 3 inches left to right horizontal manual adjustment Open/close platen speed is programmed up to 1200 inches per minute Platen hole layout of 5 inches x 5 inches grouped pattern with drilled and tapped holes Platen parallel movement achieved by a gear and rack mechanism Automatic gates on press operator side with electrical and hydraulic safeties Rear safety gate with manual door with electrical and hydraulic safeties Notes: - Tonnage occurs with high-pressure cylinders, which work off a regenerative hydraulic system for fast close - Lock up tonnage is immediate due to positive pressure on all closing cylinders - this eliminates vacuum on one platen, which results in dwell time of lock up pressure - there is no shock in this system - The platens are designed to stop on centerline with no side shifting movement on lock up and decompress HYDRAULIC UNIT 120 gallon JIC style reservoir mounted on a pedestal 50 HP electric motor, 230/460 volts Tandem radial piston pump arrangement Re-circulation (kidney) loop consisting of the following: - 2.5 HP electric motor, 230/460 volts - 6 gpm gear pump Hydraulic power unit is mounted inside machine base to allow for ease of maintenance and service CLAMP AND AUXILIARY MANIFOLDS/VALVES Proportional control hydraulic valves with On-Board-Electronics (OBE) are provided for flow control as well as pressure control (decompress and tonnage) on the clamp A full flow blocking safety cartridge valve with electric position monitoring is provided Two auxiliary valve stations are provided for hydraulic functions HEAD MANIFOLDS AND VALVES A zero lap servo solenoid control valve with OBE is provided for parison programming of each head A zero lap servo solenoid and flow control valve with OBE is provided for parison shoot and fill of each head AUTOMATIC HEAD FILL BALANCING FOR DUAL HEAD OPERATION * During filling of the heads, oil flows out of the head end of the shot cylinders as the rod retracts back into the cylinder bodies - the MACO EL controller and the fill hydraulic proportional valves provide closed loop position fill control - Under this control mode, the exhaust oil flow rate is automatically regulated, by the program, through the proportional valve settings - This method allows for balancing the dual heads well within 1% difference from head to head A pressure transducer is used to monitor shot or fill pressure on the shooting/fill cylinders Notes: - All valve manifolds are supplied with pressure gauge fittings - All valve manifolds are mounted in serviceable locations with clear identification tags for all valves AIR VALVES NINE (9) STATION Prewired Flow/pressure controls and gauges included System with automatic air pump safety circuit Actual air valves to be determined at time of order Plug and play electrical hook up Main blow 1.25 inch valve All others 1.375 inch valves MICROPROCESSOR CONTROL STATION Operator Station including: - MACO EL CRT Monitor - Operator set-up controls are push buttons Main Controller Section: - Houses all microprocessor cards - Fan cooled AC VARIABLE FREQUENCY DRIVE MOTOR CONTROLS AND HEATER CONTROL PANELS Main cabinet Voltage 460 volts, 3 phase, 60 cycle Fan cooled Heater zones with solid state contactors and circuit breakers Over temperature trip All control voltage is 24 VDC * All control wire is shielded from high power wires to minimize noise interference
----------------------------------- NOTE: Although machinery descriptions are believed to be accurate and are from sources deemed reliable, they are not guaranteed and we invite your inspection prior to purchase.
We are one of the largest stocking dealers of plastics molding machinery in the United States, and have been selling plastics machinery worldwide for over 35 years. Our inventory is constantly changing, and we are often liquidating complete plants. Please keep in contact with us so that we can keep you informed of our latest purchases.
Close This Window