Timberline Machinery Inc.
7 Pittsburgh Ave                           Nashua, New Hampshire 03062, USA
Phone (603) 889-7233         Fax (603) 889-7300        Call Ed Makepeace

Close This Window

   Request Quotation or Additional Information

   Make an offer on this machine!


2000 vintage Sterling 30 pound blow molder, complete 55 gallon drum package available !!

Ref #

Manufacturer

Model

Year

Shot Capacity (pounds)

Head Configuration

Comments

30144 

Sterling Davis-Standard 

SE630 

2000 

30 

single 

like-new blow molder, complete 55 gallon (220 liter) L-ring drum package available  


JUST AVAILABLE!
THIS 55 GALLON (225 LITRE) DRUM MOLDING PACKAGE WILL NOT LAST LONG!

2000 STERLING DAVIS-STANDARD 
SINGLE 30 POUND (13.1 KG) ACCUMULATOR HEAD BLOW MOLDER

PERFECT FOR 55 GALLON (225 LITRE) DRUMS!
Optionally available as a complete package drum molding system including:
  - like-new modern 55 gallon L-ring drum mold
  - heavy duty bottom blow stand with spreader and 
    double unscrewing threaded-cap capability

* THE BOTTOM BLOW STAND ASSEMBLY WITH SPREADER AND DOUBLE UNSCREWING CAPABILITY 
AS SHOWN IN PHOTO ABOVE IS NOT INCLUDED WITH THIS MACHINE - IT IS OFFERED WITH
THE 55 GALLON DRUM MOLDS DETAILED IN OUR REFERENCE NUMBER 90041

Excellent condition

OFFERED AS COMPLETE 55 GALLON (225 LITRE) DRUM BLOW MOLDING SYSTEM
- OR -
STAND-ALONE 30 POUND (13.1 KG) ACCUMULATOR HEAD BLOW MOLDING MACHINE

SPECIFICATIONS:

* CLAMP TONNAGE: 100 TONS
* EXTRUDER SIZE: 6 INCH DIAMETER, 24:1 L:D, grooved for high output
* EXTRUDER DRIVE:  400HP DC
* PLASTICIZING CAPACITY: 1,650 LB/HR
* SHOT SIZE: SINGLE 30 POUND (13.1 kg) HEAD
* HEAD CONFIGURATION: SINGLE
* CONTROLS: BARBER COLEMAN MACO 6500 
* 100 POINT PARISON PROGRAMMER
* 48 INCH WIDE X 56 INCH LONG CLEAR PLATEN
* AUTOMATIC PART TAKE OUT
* 66 inch maximum clamp open daylight 
* 10 inch minimum clamp closed daylight
* Tooling range is 4.5 to 18 inches
* Vertical platen height adjustment     +/- 4 inches
* Side to side platen adjustment         +/- 3 inches
* Front to back platen adjustment       +/- 3 inches
* Manual press shut height adjustment


Additional specifications:

EXTRUDER SECTION:
* Model 600 gear reducer with mechanical rating of 450HP at 100 RPM screw speed
* Continuous extrusion
* High performance feed screw with Colmonoy 56 hard surface flights 
* Sterling barrel assembly fabricated of 4140 alloy steel with bimetallic inlay of Xaloy 102 or equivalent 
  and a bolt type front flange.
* Cast aluminum heaters with integral cooling coils.
* Closed loop cooling system.
* Rupture disk, pressure reducer and indicator.

ACCUMULATOR HEADS:
* First in, first out material flow
* Common shooting ring and six push rods
* Servo valve and DC transducer
* Flow (speed) control of accumulator shooting with digital readout

CLAMP SECTION:
* Relative platen speed   1200 inches per minute
* Mechanical adjustable stops to perform as movable guide rods 

MICROPROCESSOR MACHINE CONTROL:
* Maco 6500
* Touch-Trol operator station
     Remote and accessible with swing-away feature
     Set-up operation control buttons and switches
     Ammeter, tachometer, and speed control for DC drive
     Pressure indicator
* System/ Insta-set module
* Sequence module
* Five heat/cool module - six zones
* Temperature heat only modules - three 4-zones
* Linear positioning
* Multi-parameter process control speed for parison drop
* Pressure flow module
* Cabinet is provided with space for a maximum of 15 modules

MAIN ELECTRICAL CONTROL PANEL:
* Three door construction
* Motor starter for main hydraulic AC motor
* Ammeters on each heater zone for heater burn-out detection
* Mercury contactors with circuit breakers on heater zones
* Isolation transformer for microprocessor
* Main disconnect switch
* DC drive controls
* Panel climate control devise
* Voltage regulator

PROPORTIONAL HYDRAULIC POWER UNIT:
* 200 gallon tank capacity
* 40HP AC motor
* Pre-piped and pre-wired
* Single head operation
* Return line filtration 10 micron
* Heat exchanger 27 HP with inlet temperature of 85F and oil flow of 8 GPM
* Independent recirculating system for hydraulic heat exchangers with independent pump and motor
* Three (3) 10-gallon accumulators
* Pump pressure compensated and fixed 20.8 GPM
* Necessary valves for blow mold operation of press and head
* Shooting and clamp manifolds for valve mounting
* Electronic control system

MAIN BASE HOUSES THE FOLLOWING:
* Extruder
* Accumulator head
* Hydraulic unit
* Control cabinet
* Press

AIR BLOW SYSTEM
* 11 station system, Mac air valves

PRIMARY POWER WIRING:
- Maco 6500 is designed to operate from a 102-132 VAC, 50/60 Hz, single phase power source.  
Each module contains its own power supply which provides all operating voltages for the module 
circuitry.  Control equipment should not be connected to power sources subject to extreme voltage 
fluctuations caused by switching heavy loads. A voltage step-down isolation or voltage regulation 
transformer installed in the control cabinet is supplied.

-----------------------------------

NOTE: Although machinery descriptions are believed to be accurate and 
      are from sources deemed reliable, they are not guaranteed and we 
      invite your inspection prior to purchase.
We are one of the largest stocking dealers of plastics molding
machinery in the United States, and have been selling plastics
machinery worldwide for over 35 years. Our inventory is constantly
changing, and we are often liquidating complete plants. Please keep
in contact with us so that we can keep you informed of our latest
purchases.

Close This Window