|
| 7 Pittsburgh Ave PO Box 1109 Nashua, New Hampshire, USA 03061 |
| Phone (603) 889-7233 Fax (603) 889-7300 Call Ed Makepeace |
| |
| |
| |
| |
Click on photo for larger view (133K image file)
One 1988 Engel Model ES 80 injection molding machine from ISO 9002 facility - immaculate!
82.5 ton toggle clamp
3.8 ounce (100 gram) shot
ES 240 injection unit (240 cc volume)
Repro P34W solid state controls
potentiometric controls of all strokes
digital clamp force tonnage indicator
additional 220, 440, and 110 volt accessory plugs
three 240 volt mold manifold heating zones, with plugs mounted on top of stationary platen
We don't forget you after the sale ! Call ED MAKEPEACE (603) 889-7233, FAX (603) 889-7300
| SPECIFICATIONS Clamping Unit Clamping force Clamp opening force Clamp stroke (max) Mold height (min-max) Daylight (min-max) Platen size (HxV) Tie rod diameter Hydraulic ejector force |
U.S. tons U.S. tons inches inches inches inches inches inches |
82.5 11.44 11.81 5.91 x 14.96 5.91 x 26.77 20.07 x 21.73 2.36 3.94 |
| Injection Unit Shot size, PS Injection capacity Screw diameter Plasticizing capacity max Recovery rate Injection rate Injection velocity Screw stroke Injection pressure Screw speed range Screw torque Screw L/D ratio Nozzle stroke Nozzle force Hydraulic pump capacity System pressure Oil reservoir capacity Electrics Total rated HP Number of heat control zones Total heating wattage |
ounces cu. ounces inches lbs./hr ozs./sec. cu in/sec. inches/sec inches p.s.i. rpm in./lbs inches tons gpm p.s.i. U.S. gal kw |
3.59 6.90 1.101 135 0.60 4.80 4.38 6.30 20-350 3.470 20:1 11.81 4.86 17.83 2,175 42.22 20 3 4.95 |
| General Dry cycle performance Water requirements (max) Machine dimensions (l.w.h.) Machine weight Hopper capacity |
sec gpm inches lbs. lbs. |
1.5 6.0 166.97 x 57.99 x 71.97 7.874 175 |
STANDARD EQUIPMENT
Clamping Unit - SPI standard platen and K.O. pattern - Double toggle clamp - Multi-stroke hydraulic ejection, with speed and pressure controls - 2 speed opening and closing - Electrically gear-driven central mold height adjustment - Heavy tie-bars, large bearing surface area for moving platen - Water-cooled stationary platen - Central automatic lubrication with pressure system protection - Mechanical safety drop bar with limit switch - Hydraulic electric and electronic safety gate interlock - Divided safety gate - Low pressure mold protection with digital setting
Injection Unit - 20:1 l:D nitrided barrel and screw - Non returning check valve - Digital screw indicator - 3 injection speeds - Second stage injection pressure, time and stroke dependent - Cold start protection - Rapid screw pulling from back - Water-cooled feed throat with thermometer - Programs for sprue break, decompression, intrusion, back pressure, and transition boost to hold
Hydraulics - Fully proportional linearized hydraulics - Variable displacement pump - 10 micron pressure filtration with electrical dirt alarm - Filter magnet - Oil tank with temperature and level indicator - Selective readouts for all pressures - Oil prewarming system with high and low limit L.E.D temperature readout, electrical water valve, and closed loop oil temperature control
Electric and Electronic - REPRO 2000 P control for digital settings of all pressures and speeds - Selectable manual, semi automatic, and fully automatic modes - Diagnostics with 18 L.E.D.alarm indicators L.E.D.indicators for sequence, solenoids, and position controls - Electronic temperature controls with barrel - Delay timers for plasticizing and spruce break - Cycle and hour counters - Separate controls for heat and drive - Circuit breakers i.p.o. fuses - Verified control panel - High energy-efficient, totally enclosed fan cooled motor - Hydro approved (equivalent of C.S.A. and U.L.)
General - Easy access to motors, pumps & hydraulics - Large open drop area for automation